[AsteriskBrasil] Problema com Placa Billion RDSI.
Pedro Jorge Viana de Bragança Menezes
pedro em s3p.es
Segunda Maio 14 16:04:38 BRT 2007
From: Pedro Jorge Viana de Bragança Menezes [mailto:pedro em s3p.es]
To: asteriskbrasil em listas.asteriskbrasil.org
Sent: Mon, 14 May 2007 17:36:47 +0200
Subject: [AsteriskBrasil] Problema com Placa Billion RDSI.
Boa Tarde a todos,
Tenho um problema com uma placa Billion RDSI, configuro um TrixBox 2.2, faço o instal-ZAPHFC, reconfigura tudo tranquilo, sem problemas, Tanto a TDM400P com 2 Fxo e 1 FXS e a placa RDSI.
O problema é que depois de um tempo aparece esse erro em dmesg:
#zaphfc: bchan rx fifo not enough bytes to receive! (z1=912, z2=905, wanted 8 got 7), probably a buffer overrun.
#zaphfc: bchan rx fifo not enough bytes to receive! (z1=922, z2=915, wanted 8 got 7), probably a buffer overrun.
#Registered tone zone 6 (Spain)
#zaphfc: bchan rx fifo not enough bytes to receive! (z1=3170, z2=3163, wanted 8 got 7), probably a buffer overrun.
#zaphfc: bchan rx fifo not enough bytes to receive! (z1=3932, z2=3925, wanted 8 got 7), probably a buffer overrun.
Depois de um tempo sai este erro:
# zaphfc: sync lost, performance too low. you might have some cpu throtteling.
Depois de um bom tempo o audio das ligacoes sao insuportaveis, com muita interferencia e o erro em dmesg se dispara....
Estive pesquisando nos foros de trixbox.org e falam de um parche, mas indicam que só é recomendavel a partir de duas placas ISDN.
Já baixei o PCI LATENCY TIMER em 32, parece que nao me ajuda muito....
Aqui envio uma copia dos arquivos .conf que tenho e um lspci.
-------------------------------------------------------------------------------------------------------------------------------------------------
lspci -vb:
00:00.0 Host bridge: Broadcom GCNB-LE Host Bridge (rev 32)
Flags: fast devsel
00:00.1 Host bridge: Broadcom GCNB-LE Host Bridge
Flags: fast devsel
00:03.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5702X Gigabit Ethernet (rev 02)
Subsystem: Compaq Computer Corporation NC7760 Gigabit Server Adapter (PCI-X, 10/100/1000-T)
Flags: bus master, 66Mhz, medium devsel, latency 64, IRQ 4
Memory at 00000000fe000000 (64-bit, non-prefetchable)
Capabilities: [40] PCI-X non-bridge device.
Capabilities: [48] Power Management version 2
Capabilities: [50] Vital Product Data
Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/3 Enable-
00:04.0 SCSI storage controller: Adaptec AIC-7892A U160/m (rev 02)
Subsystem: Adaptec 29160 Ultra160 SCSI Controller
Flags: bus master, 66Mhz, medium devsel, latency 32, IRQ 3
BIST result: 00
I/O ports at d800 [disabled]
Memory at 00000000fd800000 (64-bit, non-prefetchable)
Capabilities: [dc] Power Management version 2
00:06.0 Network controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface
Subsystem: Unknown device b119:0001
Flags: bus master, medium devsel, latency 32, IRQ 7
I/O ports at d400
Memory at fd000000 (32-bit, non-prefetchable)
Capabilities: [40] Power Management version 2
00:07.0 Network controller: Cologne Chip Designs GmbH ISDN network controller [HFC-PCI] (rev 02)
Subsystem: Cologne Chip Designs GmbH ISDN Board
Flags: bus master, medium devsel, latency 16, IRQ 11
I/O ports at d000 [disabled]
Memory at fc800000 (32-bit, non-prefetchable)
Capabilities: [40] Power Management version 1
00:09.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27) (prog-if 00 [VGA])
Subsystem: Compaq Computer Corporation Proliant Rage XL
Flags: bus master, stepping, medium devsel, latency 32, IRQ 12
Memory at fb000000 (32-bit, non-prefetchable)
I/O ports at b800
Memory at fa800000 (32-bit, non-prefetchable)
Expansion ROM at feba0000 [disabled]
Capabilities: [5c] Power Management version 2
00:0f.0 ISA bridge: Broadcom CSB6 South Bridge (rev a0)
Subsystem: Broadcom: Unknown device 0201
Flags: bus master, medium devsel, latency 32
00:0f.1 IDE interface: Broadcom CSB6 RAID/IDE Controller (rev a0) (prog-if 8a [Master SecP PriP])
Subsystem: Broadcom: Unknown device 0212
Flags: bus master, medium devsel, latency 64
I/O ports at b400
I/O ports at b000
I/O ports at a800
I/O ports at a400
I/O ports at a000
00:0f.2 USB Controller: Broadcom CSB6 OHCI USB Controller (rev 05) (prog-if 10 [OHCI])
Subsystem: Broadcom: Unknown device 0220
Flags: bus master, medium devsel, latency 32, IRQ 10
Memory at fa000000 (32-bit, non-prefetchable)
00:0f.3 Host bridge: Broadcom GCLE-2 Host Bridge
Subsystem: Broadcom: Unknown device 0230
Flags: bus master, medium devsel, latency 0
-------------------------------------------------------------------------------------------------------------------------------------------------
#cat /proc/zaptel/*
Span 1: WCTDM/0 "Wildcard TDM400P REV I Board 1"
1 WCTDM/0/0 FXSKS (In use)
2 WCTDM/0/1 FXSKS (In use)
3 WCTDM/0/2
4 WCTDM/0/3 FXOKS (In use)
Span 2: ZTHFC1 "HFC-S PCI A ISDN card 0 [TE] layer 1 ACTIVATED (F7)" AMI/CCS
5 ZTHFC1/0/1 Clear (In use)
6 ZTHFC1/0/2 Clear (In use)
7 ZTHFC1/0/3 HDLCFCS (In use)
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
# cat /etc/zaptel.conf
# Span 1: WCTDM/0 "Wildcard TDM400P REV I Board 1"
fxsks=1
fxsks=2
# channel 3, WCTDM, inactive.
fxoks=4
# Span 2: ZTHFC1 "HFC-S PCI A ISDN card 0 [TE] layer 1 DEACTIVATED (F4)" AMI/CCS
# ??: 5 ZTHFC1/0/1 Clear
# ??: 6 ZTHFC1/0/2 Clear
# ??: 7 ZTHFC1/0/3 HDLCFCS
# Global data
loadzone = es
defaultzone = es
# HFC CARD NOTE:
# When run for the first time the card numbers start from 1
# When run subsequently the card numbers start from 0
# Go figure!
# Span 2: ZTHFC1 "HFC-S PCI A ISDN card 1 [TE]"
span=2,1,3,ccs,ami
bchan=5-6
dchan=7
------------------------------------------------------------------------------------------------------------------------
# cat /etc/asterisk/zapata-BRI-HFC.conf
; Basic ISDN Card TE mode config
resetinterval=never
immediate=no
switchtype=euroisdn
signalling=bri_cpe
pridialplan=dynamic
prilocaldialplan=local
nationalprefix=0
internationalprefix=00
usecallingpres=yes
echocancel=yes
echocancelwhenbridged=yes
echotraining=100
context=from-zaptel
group=0
channel => 5-6
----------------------------------------------------------------------------------------------------------------
[root em voip src]# cat /etc/sysconfig/zaptel
TELEPHONY=yes
#DEBUG=yes
# Un-comment as per your requirements; modules to load/unload
# genzaptelconf will populate this file
#Module Name Hardware
#MODULES="$MODULES tor2" # T400P - Quad Span T1 Card
# E400P - Quad Span E1 Card
#MODULES="$MODULES wct4xxp" # TE405P - Quad Span T1/E1 Card (5v version)
# TE410P - Quad Span T1/E1 Card (3.3v version)
#MODULES="$MODULES wct1xxp" # T100P - Single Span T1 Card
# E100P - Single Span E1 Card
#MODULES="$MODULES wcte11xp" # TE110P - Single Span T1/E1 Card
#MODULES="$MODULES wcfxo" # X100P - Single port FXO interface
# X101P - Single port FXO interface
MODULES="$MODULES wctdm" # TDM400P - Modular FXS/FXO interface (1-4 ports)
#MODULES="$MODULES wcfxs" # either above or this
#MODULES="$MODULES wcusb" # S100U - Single port FXS USB Interface
#MODULES="$MODULES wcfxsusb" # either above or this
#MODULES="$MODULES torisa" # Old Tormenta1 ISA Card
#MODULES="$MODULES ztdummy" # UHCI USB Zaptel Timing Only Interface
MODULES="$MODULES zaphfc" # HFC ISDN module
------------------------------------------------------------------------------------------------------------------------------------------
[root em voip src]# cat /etc/rc.local
#!/bin/sh
#
# This script will be executed *after* all the other init scripts.
# You can put your own initialization stuff in here if you don't
# want to do the full Sys V style init stuff.
touch /var/lock/subsys/local
/etc/trixbox/runonce
/usr/local/sbin/motd.sh > /etc/motd
/sbin/udevstart
/usr/sbin/ztcfg
/sbin/fxotune -s
/usr/sbin/amportal start
------------------------------------------------------------------------------------------------------------------------------------------
Muito obrigado por qualquer ajuda...
Um abraco.
Le informamos, como destinatario de este mensaje, que las comunicaciones a través del presente instrumento no permiten asegurar ni garantizar la confidencialidad de los mensajes transmitidos,así como tampoco su integridad o correcta recepción, por lo que S3P no asume ningún tipo de responsabilidad por tal circunstancia. Si no consintiese en la utilización del presente medio para el envío de comunicaciones le rogamos nos lo comunique a la mayor brevedad posible.
Este mensaje tiene carácter confidencial y es para el exclusivo uso del destinatario indicado en la misma.
Si Vd. no es el destinatario indicado, se le informa de que cualquier forma de distribución, reproducción o uso de esta comunicación y/o de la información contenida en la misma está estrictamente prohibida y resultaría ilegal.
Si Vd. ha recibido esta comunicación por error, por favor, notifíquelo inmediatamente al remitente mediante email y proceda a continuación a destruirlo.
-------------- Próxima Parte ----------
Um anexo em HTML foi limpo...
URL: http://listas.asteriskbrasil.org/pipermail/asteriskbrasil/attachments/20070514/5bccf152/attachment.html
Mais detalhes sobre a lista de discussão AsteriskBrasil